View HT7A6003_3113123.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev. 1.00 1 may 27, 2011 rev. 1.00 pb june 21, 2011 HT7A6003 emi-improved green mode pwm controller with integrated protections feature ? frequency jitter for restraining emi ? integrated soft-start function ? very low operating current and start-up current (<20 m a) for satisfying energy-star 2.0 "no-load mode" (stand-by) power standard ? 5% trimmed oscillator for precise frequency ? programmable switching frequency ? non-audible-noise green mode control ? leb (leading-edge blanking) on cs pin ? internal slope compensation ? cycle-by-cycle current limiting ? short-circuit-protection(scp) for short-circuit and over-load condition ? over-voltage-protection(ovp) on vcc pin ? 8-pin sop package applications ? switching ac-dc adaptor ? open frames switching power supply ? ups ? lcd tv general description HT7A6003 is an advanced, highly integration of f- line pwm controller . this device provides many protection functions with ultra low power circuit design, and i s optim ized for rest raining emi. by integrated a non-audible noise green mode control scheme and optimizing for the ener gy star 2.0 spec., the power supply unit (psu) implemented using the ht 7a6003 c an sa tisfy t he energy st ar no - load mode stand-by power standard, which is less than 0.3w w ithin all n ameplate o utput p ower range of 0~250w . this device also integrated various protection functions such as short-circuit protection (scp, wh ich c an a lso be use d for ov er-load protection, ol p), c ycle-by-cycle c urrent l imiting, over v oltage protection (ovp), and soft-start function f or r educing i nrush c urrent d uring sy stem initialization and preventing device burn-out. the HT7A6003 also integrates leading-edge blanking and sl ope compe nsation for m inimizing external components cost and system complexity. application circuits emi filter flyback converter ht 7a 6003 rt gd cs vcc comp vref gnd 0.1 uf 10 k fod 817 tl 431 25k 95 k gnd vout current sense voltage sense
rev. 1.00 2 may 27, 2011 HT7A6003 block diagram pin assignment 32 v uvlo 14v / 8v internal bias & vref slop compensation pwm 2r r ocp 1v leb 350ns scp s r q driver stage vref vcc gd gnd vcc rt comp cs ovp frequency jitter green mode osc soft - start pin description pin no. pin name description 1 comp voltage feedback pin. connected to a photo-coupler for close-loop control. 2 n.c no connection 3 cs a voltage proportional to inductor current is connected to this input. the pwm generator uses this voltage information to terminate the output switch conduction. 4 rt the oscillator frequency is programmed by connecting a resistor rt between this pin and ground. a maximum frequency of 500khz is possible. 5 gnd combined control circuitry and power ground. 6 gd power mosfet gate driver output. 7 vcc positive supply. 8 vref reference output. absolute maximum ratings supply v oltage vcc ................................................................................................................................ -0.3v~30.0v comp , rt, cs pins ................................................................................................................................... -0.3v~5.5v junction t emperature .......................................................................................................................................... 150c operating ambient t emperature ............................................................................................................... -40c~85c storage t emperature range .................................................................................................................... -65c~150c package thermal resistance (8-pin sop) ..................................................................................................... 160c/w esd protection: human body model ............................. ......................................................................................................... 3kv machine model ............................ ............................................................................................................... 200v note: these are stress ratings only . stresses exceeding the range specifed under absolute maximum ratings may cause substantial damage to the device. functional operation of this device at other conditions beyond t hose l isted i n t he sp ecifcation i s n ot i mplied a nd p rolonged e xposure t o e xtreme c onditions m ay a ffect device reliability. 1 2 3 4 8 7 6 5 comp nc cs rt vref vcc gd gnd ht 7a 6003 8 sop -a
rev. 1.00 3 may 27, 2011 HT7A6003 electrical characteristics unless otherwise stated, this specifcations apply for 0c ta 70c, v cc =15v, rt=10k w symbol parameter test condition min. typ. max. unit supply voltage (vcc pin) i st startup current v cc =12.9v 12 30 m a i cc operating current v comp =0v 2.0 3.0 ma v comp =3v 2.5 ma v tl uvlo (off) 7 8 9 v v th uvlo (on) 13 14 15 v v cc ovp trip level vcc(over voltage protection) 26.5 28.0 29.5 v v cc ovp strobe time 80 m s reference section v ref output voltage tj = 25c, i o = 1ma 5.5 v ?v ref line regulation 12v v cc 25v 3 20 mv ?v ref load regulation 1ma i o 10ma 4 25 mv current sensing (cs pin) v cs(off) maximum input voltage, vcs(off) 0.9 1.0 1.1 v t leb leading edge blanking time 350 ns t d-ovp delay to output 100 ns oscillator (rt pin) f osc oscillator frequency tj=25c, rt=10k w 49 52 55 khz ?f osc ?t a temperature stability -40c ~105c 5 % ?f osc ?v ref voltage stability v cc =10v~25v 0.2 1.0 %/v d max maximum duty 75 % frequency jitter 4 % gate drive output (gd pin) v ol output low level v cc =15v, isink=20ma 1 v v oh output high level v cc =15v, isource=20ma 9 v t r rising time tj=25c, load capacitance=1nf 50 150 ns t f falling time tj=25c, load capacitance=1nf 50 150 ns voltage feedback (comp pin) i sink short circuit current v comp =0v 1.5 2.2 ma v comp open loop voltage comp pin open 5.5 v scp (short circuit protection) v comp scp trip level v comp (scp) 4.7 v scp delay time (see note) f s =52khz 40 ms soft-start t start soft-start time rt=10k w 8.5 ms 1rwh 7khvh 3dudphwhuv dowkrxjk jxdudqwhhg duh qrw whvwhg lq surgxfwlrq
rev. 1.00 4 may 27, 2011 HT7A6003 typical performance characteristics 11 .5 12 12 .5 13 13 .5 14 14 .5 15 15 .5 - 40 - 20 0 20 40 60 80 100 120 temperature ( degree c ) uvlo (on)(v) figure 1. uvlo (on) (v) vs. temperature 47 48 49 50 51 52 53 54 55 56 57 - 40 - 20 0 20 40 60 80 100 120 temperature ( degree c ) frequency (khz) figure 3. frequency vs. temperature 4.4 4. 45 4.5 4. 55 4.6 4. 65 4.7 4. 75 4.8 4. 85 4.9 - 40 - 20 0 20 40 60 80 100 120 temperature ( degree c ) vcomp (v) figure 5. vcomp for scp vs. temperature 6 6.5 7 7.5 8 8.5 9 9.5 10 - 40 10 60 110 temperature ( degree c ) uvlo (off)(v) figure 2. uvlo (off)(v) vs. temperature 47 48 49 50 51 52 53 54 55 56 57 11 13 15 17 19 21 23 25 vcc (v) frequency (khz) figure 4. frequency vs. vcc 15 17 19 21 23 25 27 29 31 11 13 15 17 19 21 23 25 vcc (v) green mode frequency (khz) figure 6. green mode frequency vs. vcc
rev. 1.00 5 may 27, 2011 HT7A6003 application information operation overview the HT7A6003 is a highly function-integrated off-line pwm controller which is optimized for applications that needs strong em i-restraining and various abnormal conditions protecting capability . this device has a wide operating temper ature range (-40 c t o 85 c ), a nd provi des m any prot ection func tions such as cycle-by-cycle current limiting, scp/ ol p, ovp , a nd so ft-start f unction,, t hat e nsure t he system implemented by HT7A6003 can operate very stably at extreme environment like outdoor with ultra low temperature (-40 c , the polar region), or high emi environment (factory or the region with highly e lectromagnetic wa ve). t he de vice i s op timized fo r the energy-star 2.0 specifcation, this ensures that any eps (external power supply) implemented using the ht 7a6003 c an f ully sa tisfy t he e nergy st ar 1 .1/2.0 stand-by (no-load) criteria. energy consumption criteria for no-load nameplate output power (p no ) maximum power in no-load ac-ac eps ac-dc eps 0 to < 50 watts 0.5 watts 0.3 watts 50 to 250 watts 0.5 watts 0.3 watts table 1: energy star 2.0 no-load criteria ultra low stand-by power for energy star 2.0 and later energy star requirement the device contains many advanced control schemes for low stand-by power like tiny operating/stand- by current, green mode for light-load, etc. by c hoosing a n a ppropriate st and-by re sistor (a s shown i n fi g. 7) , e ps i mplemented by t he de vice c an fu lly satisfy the energy star 2.0 no-load criteria. figure 7. stand-by resistor base on device feld test demo board results, for the full-range (1 15v, 230v v ac) input, the stand-by power will remain less than 0.3w@pno=60w(as shown in t able 2).this is within the ener gy star 2.0 criteria. input range stand-by power demo board input condition (p no =60 watts) 115v v ac < 0.3w 230v v ac < 0.3w table 2. demo board stand-by power results advanced precise-oscillator for green-mode switching and non-acoustic noise requirement a t rimmed precise green mode oscillator is implemented in the device to enhance the conversion ef ficiency under conditions of light loads. as the da ta shown i n fi g. 8, t he e ffciency di fference of t he traditional current mode pwm controller between light loads and heavy loads is more than 8%, while t he a verage e fficiency i s onl y 82% , t he e fficiency dif ference of the HT7A6003 is only 1%, while average effciency is up to 87.5%. figure 8. effciency comparison between HT7A6003 & traditional current mode pwm controller (measured at ht7a3942 demo board)
rev. 1.00 6 may 27, 2011 HT7A6003 the gre en mode osc illator t ypes suppli ed by ot her pw m c ontroller pr oviders a re pl agued by t he problems of acoustic-noise. this is because, under the conditions of light loads, the frequency will keep de creasing t hrough hum an ac oustic ra nge (from 20hz to 20khz), these audio frequencies may create audible noise in the transformer . holtek s HT7A6003 patented green mode oscillator designed using an a dvanced non-acoust ic noi se schem e t o pre vent t he ge neration of fre quencies i n t he a udio fre quency band, thus eliminating any transformer noise. figure 9. oscillator behavior compared with HT7A6003 and other green mode pwm controller under voltage lockout (uvlo) an uvl o c omparator i s i mplemented i n t o e nsure that the device is fully functional before the output st age i s e nabled. as sh own i n fi g. 1 0, a h ysteresis is provided to prevent the pwm controller from sh utting d own d uring a ny v oltage d ips wh ich m ight occur during startup proces s. the turn-on and turn- of f threshold levels are set at 16.0v and 10.0v , respectively . figure 10. uvlo scheme and start-up current current sense and leading-edge blanking (leb) a leading-edge blanking scheme is integrated in the device to prevent false triggerin g due to feedback current spi kes whi ch m ay appea r on t he cs pin, further eliminate the need for r-c filter which is alw ays a requirement in the traditional current mode pwm controller applications. figure 11. leb with r-c filter removed
rev. 1.00 7 may 27, 2011 HT7A6003 internal slope-compensation an i mportant i ssue wi th t he c urrent m ode c ontrol schemes is the instability due to sub-harmonic oscillation when the duty-cycle > 50%. t o prevent this problem from occurring, a sl ope-compensation fu nction i s a lways n ecessary. in t raditional c urrent m ode pw m cont roller a pplication, m any e xternal components are necess ary for s lope-compensation function, but in ht7a3942 the internal slope- com pensation e liminates t he ne ed for t hese e xternal components resulting in simplified the application circuit design. short-circuit protection (scp) and over-load protection (olp) to p rotect a ll t he d evices of a syst em f rom be ing damaged under over load or short circuit conditions, a sm art scp func tion i s i mplemented i n t he de vice. here the feedback system will force the voltage loop to move toward a saturat ion value and then pull up the voltage on the comp pin. whenever the vcomp increases to the scp threshold of 4.7v and remains t here for l onger t han 40ms, t he prote ction sc heme will activate and then turn of f the gate output to stop the switching of power circuit. by using such a protection mechanism, the average input power can be reduced to a very low level so that the component temperature and stress can be controlled within safe operating levels. figure 12. scp function behavior over-voltage protection (ovp) on vcc pin vcc ov er-voltage pr otection i s i ntegrated i n t his device to prevent components damage due to over voltage condition on vcc pin. the ovp is triggered whe n vcc re aches 28v a nd l asts for 80 m s, and t he pwm pulses are disabled when ovp is enabled. frequency jitter for emi restraining emi r estraining i s a ccomplished b y fr equency ji tter function, which spreads the ener gy over a wider f requency r ange t han t he b andwidth m easured b y t he e mi t est e quipment. an i nternal fre quency ji tter circuit changes the switching frequency between +4% and -4% of central frequency with a period of 4ms. oscillator frequency tuning by choos ing an appropriate value of an external resistor between the r t pin and gnd, a suitable operating frequency can be generated. the relationship between the value of r t and the operating frequency is provided in the figure 13. figure 13. rt resistor value vs. operating frequency
rev. 1.00 8 may 27, 2011 HT7A6003 package information 8-pin sop (150mil) outline dimensions ms-012 symbol dimensions in inch min. nom. max. a 0.228 D 0.244 b 0.150 D 0.157 c 0.012 D 0.020 c' 0.188 D 0.197 d D D 0.069 e D 0.050 D f 0.004 D 0.010 g 0.016 D 0.050 h 0.007 D 0.010 0 D 8 symbol dimensions in mm min. nom. max. a 5.79 D 6.20 b 3.81 D 3.99 c 0.30 D 0.51 c' 4.78 D 5.00 d D D 1.75 e D 1.27 D f 0.10 D 0.25 g 0.41 D 1.27 h 0.18 D 0.25 0 D 8
rev. 1.00 9 may 27, 2011 HT7A6003 reel dimensions sop 8n (150mil) symbol description dimensions in mm a reel outer diameter 330.01.0 b reel inner diameter 100.01.5 c spindle hole diameter 13.0 +0.5/-0.2 d key slit width 2.00.5 t1 space between flange 12.8 +0.3/-0.2 t2 reel thickness 18.20.2
rev. 1.00 10 may 27, 2011 HT7A6003 carrier tape dimensions

sop 8n (150mil) symbol description dimensions in mm w carrier tape width 12.0 +0.3/-0.1 p cavity pitch 8.00.1 e perforation position 1.750.10 f cavity to perforation (width direction) 5.50.1 d perforation diameter 1.550.1 d1 cavity hole diameter 1.50 +0.25/-0.00 p0 perforation pitch 4.00.1 p1 cavity to perforation (length direction) 2.00.1 a0 cavity length 6.40.1 b0 cavity width 5.20.1 k0 cavity depth 2.10.1 t carrier tape thickness 0.300.05 c cover tape width 9.30.1
rev. 1.00 11 may 27, 2011 HT7A6003 holtek semiconductor inc. (headquarters) no.3, creation rd. ii, science park, hsinchu, taiwan tel: 886-3-5631999 fax: 886-3-563-1189 http://www.holtek.com.tw holtek semiconductor inc. (taipei sales offce) 4f-2, no. 3-2, yuanqu st., nankang software park, taipei 115, taiwan tel: 886-2-2655-7070 fax: 886-2-2655-7373 fax: 886-2-2655-7383 (international sales hotline) holtek semiconductor inc. (shenzhen sales offce) 5f, unit a, productivity building, no.5 gaoxin m 2nd road, nanshan district, shenzhen, china 518057 tel: 86-755-8616-9908, 86-755-8616-9308 fax: 86-755-8616-9722 holtek semiconductor (usa), inc. (north america sales offce) 46729 fremont blvd., fremont, ca 94538, usa tel: 1-510-252-9880 fax: 1-510-252-9885 http://www.holtek.com copyright ? 2011 by holtek semiconductor inc. the information appearing in this data sheet is believed to be accurate at the time of publication. however, holtek assumes no responsibility arising from the use of the specifications described. the applications mentioned herein are used solely for the purpose of illustration and holtek makes no warranty or representation that such applications will be suitable without further modifcation, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. holtek's products are not authorized for use as critical components in life support devices or systems. holtek reserves the right to alter its products without prior notifcation. for the most up-to-date information, please visit our web site at http://www.holtek.com.tw .

▲Up To Search▲

Price & Availability of HT7A6003

	To Download HT7A6003 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .